-
Alternator 17ACR, 45 Amp with Internal Regulator
1 × $181.50 -
12v/ 240v PORTABLE 45L FRIDGE FREEZER
1 × $1,228.15 -
Setscrew, Multi use
3 × $1.05 -
SENSOR - MAF
1 × $105.33 -
Hose, Engine Breather - S-Type 4.0 V8
1 × $96.53 -
HT Lead Ignition Spark Tester
1 × $49.50 -
Fan Belt, Mini/Jag XJ6/XJ12/XJS
1 × $17.60 -
Radiator Cap, 7lb Long Reach Type
1 × $8.80 -
Bolt, Front Sub Frame Tower to Body, (Dry)
1 × $13.20 -
Brake Master Cylinder, MGB, 1968 - 1974 USA Model
1 × $159.50 -
DIAGNOSTIC TOOL PRO - ALL LAND ROVER
1 × $1,650.00 -
LATCH, LHR DOOR
1 × $167.48 -
Boot Kit, Pot Joint, Inboard CV
1 × $11.50 -
BRAKE SHOE RETURN SPRING, 10" BRAKES (RED)
1 × $6.33 -
Anti-rattle Spring
1 × $1.95 -
HINGE PIN, DEFENDER VENT FLAP
1 × $6.33 -
Fuel Tank Sender Float
1 × $15.87 -
Rotor Arm, 45D Distributor
1 × $6.60 -
Brake Pad Retaining Pin Kit
1 × $13.48 -
400 amp snap connectors.
1 × $60.81 -
BEARING, REAR WHEEL - RANGE ROVER EVOQUE & JAGUAR MODELS
2 × $42.97 -
Colour Tune, Single Plug Kit, 14mm
1 × $126.50 -
Rotor Arm, Suit Ducellier Distributor
1 × $5.50 -
Exhaust Manifold Gasket
1 × $14.85
Fuel System
-
$16.50
SU needle conversion kit
Used to convert to fixed needle in floating needle type carburettors.
Mini & Moke
-
$9.90
A Worn throttle Shaft (spindle) can cause erratic performance and sometimes the housing is worn as well.Â
This bush is used on both sides of the carburettor to repair a worn carburettor body, often required when replacing the throttle shaft (spindle) on the HS4 carburettor.
As a guide the internal diameter is .3125 you may have to ream body to 9.55mm.
-
$10.45
A Worn throttle Shaft (spindle) can cause erratic performance and sometimes the housing is worn as well.Â
This bush is used on both sides of the carburettor to repair a worn HS2 carburettor body, often required when replacing the throttle shaft (spindle) on the carburettor.
Qty 2 required
-
-
-
$8.80
Tube, Air Pre-Heat Duct,Â
Fitted between the air temperature control and # 12G3213
-
$24.39
Twin Carb Choke Link Shaft.
Rod with chamfered ends about 57.2mm long (shorten to 54mm for twin HS4) which has AUE586 and AUE587 clamps to fit between SU twin carbs for the linkage.
-
$104.50
Twin Carburettor Linkage Kit
This kit will suit all the later 1.25″ and 1.5″ twin carb set ups where the balance rods between the carbs are equal in length (2.25″) Some early model carbs had the balance bar with a triangular plate, this is a shorter length.
-
$1.10
Wing Nut, Air Filter To Carburettor 1- 1/4″ SU
This a replacement wing nut to suit the air filter lid on the single HS2.
-