Serach

You have 6 item(s) in your cart

SEAL, FUEL SENDER UNIT

1 × $1.00

Remove
Electronic Ignition Conversion Kit Suit 43D, 45D & 59D Type Distributor

1 × $72.00

Remove
Blanking Plug, Various Uses

1 × $4.24

Remove
Headlamp Bucket Kit, (Bowl) Suit 7'' Lamps - CHROME BEZEL

1 × $40.00

Remove
Manifold Stud

1 × $1.54

Remove
LEFT HAND, REAR QUARTER SIDE PANEL - UK MINI

1 × $535.00

Remove

Total: $653.78

Go To Cart Check out

Engine

Temperature Transmitter

$16.50

Temperature Transmitter

Mini & Moke

MGB, MGC

Triumph TR4, TR4A

Add to cart
Temperature Transmitter, Rover Mini SPi

$35.81

Coolant Temperature Transmitter

This transmitter is denoted by it’s black plastic end. Mounted to the underside of the inlet manifold.

Add to cart
Thermostat Gasket, All ”A” & ”B” Series

$1.50

Thermostat Gasket, All ”A” & ”B” Series

Add to cart
Thermostat Housing

$24.20

Thermostat Housing, Standard Alloy

Add to cart
Thermostat Housing

$71.50

Thermostat Housing

These were fitted to late model 76>81 Moke’s and Mini’s, the outlet faces the firewall not the front like on the earlier cars.
Thermostat Housing

$55.00

Thermostat Housing, Forward Facing

With Temperature Gauge Hole
Thermostat Housing Spacer

$19.80

This is the spacer that sits between the engine support bracket and the thermostat housing on 1976 onwards (rear facing setup)

Add to cart
Thermostat Housing Stud 48mm (1.9375″) Long

$2.82

Thermostat Housing Stud 48mm (1.9375″) Long

This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required.

5/16″ unc and unf at nut end, this stud is about 5cm long about 4cm from the bottom of the UNC thread

Add to cart
Thermostat Housing Stud, 48.mm (1.9375″) Set Of 3

$5.57

Thermostat Housing Stud, 48.mm (1.9375″) Set Of 3

This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required.

5/16″ unc and unf at nut end, this stud is about 5cm long about 4cm from the bottom of the UNC thread
Thermostat Housing Stud, 52 mm

$2.86

These are the special studs for the thermostat housing – 5/16 dia x 52mm o/all length with unc one end and unf the other.

Suits housings without engine steady bracket.
Thermostat Housing Stud, 76 mm

$5.25

Thermostat Housing Stud, 76 mm

If your thermostat has a sandwich plate under it, you will need these longer studs. The washers are # GFK1114 and the nuts are # FNZ505.

5/16″ bolt 3″long, unc bolt with unf nut end.

Also used as a differential housing to case stud.

Add to cart
Thermostat Housing, 1275cc

$82.50

Thermostat Housing, to suit Late 1275 Moke and 1275 LS Mini’s.
Thermostat Housing, Plug in Top, UK Mini

$28.14

Thermostat Housing, Plug in Top

New Old Stock
Thermostat, 74c

$16.50

Thermostat, 74c

Add to cart
Thermostat, 74c, BORG & BECK

$19.58

Thermostat, 74c

Borg & Beck Brand

Add to cart