-
Gasket, Cylinder Head, Standard
1 × $16.50 -
Heater Tap
2 × $44.00 -
Fuse Box Cover
1 × $22.55 -
Thermostat Housing Stud 48mm (1.9375") Long
1 × $2.82 -
Cylinder Head Stud, Short
2 × $13.00 -
Grease Nipple Multi Use
1 × $2.70 -
By-pass Hose, Standard
3 × $5.94 -
Temperature Transmitter
2 × $16.50 -
Distributor Cap, Suit 43D, 45D & 59D Distributors. Lucas Brand
1 × $20.85 -
Headlamp Bucket Kit, (Bowl) Suit 7'' Lamps - CHROME BEZEL
1 × $40.00 -
Valve Cotter, Pair
1 × $9.90 -
WATER PUMP - 2.5L KV6
1 × $60.01 -
Water Pump Pulley
1 × $20.35 -
Thermostat Housing
1 × $24.20 -
Viscous Fan Spanner 32/36mm
1 × $55.00 -
Side Panel Rear Quarter Right Hand, UK Mini
1 × $544.50 -
Blanking Plate, Heater Tap Outlet
1 × $12.10 -
Exhaust Manifold Gasket
1 × $14.85 -
Blanking Plug, Various Uses
1 × $4.24
Engine
-
$24.20
Screw – Tappet Adjusting, 7/16 UNF , Fitted to all “Pressed” Rocker Arms
Except those fitted to the 1275cc
This screw is sold each, Qty 8 Required per vehicle
The nut fitted to this screw is # 6K654
-
-
$356.02
Temperature Pressure Compensator SPI TPC
-
-
$35.81
Coolant Temperature Transmitter
This transmitter is denoted by it’s black plastic end. Mounted to the underside of the inlet manifold.
-
-
-
$71.50
Thermostat Housing
These were fitted to late model 76>81 Moke’s and Mini’s, the outlet faces the firewall not the front like on the earlier cars.
-
$55.00
Thermostat Housing, Forward Facing
With Temperature Gauge Hole
-
$19.80
This is the spacer that sits between the engine support bracket and the thermostat housing on 1976 onwards (rear facing setup)
-
$2.82
Thermostat Housing Stud 48mm (1.9375″) Long
This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required.
5/16″ unc and unf at nut end, this stud is about 5cm long about 4cm from the bottom of the UNC thread
-
$5.57
Thermostat Housing Stud, 48.mm (1.9375″) Set Of 3
This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required.
5/16″ unc and unf at nut end, this stud is about 5cm long about 4cm from the bottom of the UNC thread
-
$2.86
These are the special studs for the thermostat housing – 5/16 dia x 52mm o/all length with unc one end and unf the other.
Suits housings without engine steady bracket.
-
$5.25
Thermostat Housing Stud, 76 mm
If your thermostat has a sandwich plate under it, you will need these longer studs. The washers are # GFK1114 and the nuts are # FNZ505.
5/16″ bolt 3″long, unc bolt with unf nut end.
Also used as a differential housing to case stud.
-
$82.50
Thermostat Housing, to suit Late 1275 Moke and 1275 LS Mini’s.