-
Apron Panel, Repair Section Front L/Hand
1 × $141.63 -
Long Male Brake Nut 3/8 UNF x 24tpi
1 × $2.42 -
Carburettor Bell & Float Screw, All SU Carburettors
1 × $0.55 -
Thermostat, 82c
1 × $11.55 -
Colour Tune, Single Plug Kit, 14mm
1 × $126.50 -
Starter Switch Push
1 × $86.90 -
Latch, Front Door RH
1 × $214.83 -
FILTER - ENGINE OIL
2 × $11.00 -
Bearing Roller Type, 1st Gear
1 × $33.00 -
Accelerator Pedal Pad, Earlier Mini
1 × $3.30 -
Wind Deflector Set Defender
1 × $69.03 -
Distributor Cap, Suit 43D, 45D & 59D Distributor
1 × $13.20 -
Timing Tool Kit - for Land Rover, Ford, Jaguar
1 × $132.00 -
BRAKE FLUID TESTER
1 × $55.00 -
RESERVOIR - POWER STEERING - FREELANDER 2 - JAGUAR - XF - XJ - INCLUDES CAP
1 × $47.74 -
Battery Lead End Insulator
1 × $3.03 -
TERRAFIRMA CENTRE SILENCER REPLACEMENT PIPE
1 × $205.70 -
Alternator 17ACR, 45 Amp with Internal Regulator
1 × $181.50 -
Wheel Cylinder Assembly Right Hand, Front
1 × $31.63 -
INTERCOOLER SILICONE HOSE KIT DISCOVERY 2
1 × $137.50 -
Setscrew, Multi use
2 × $1.05 -
Clip, Interior Trim
1 × $2.86 -
HSING & T/STAT (82c)
1 × $64.80 -
Bearing, Wheel Hub
1 × $93.50 -
BOLT KIT FRONT DOOR - STAINLES STEEL
1 × $44.83 -
HUB NUT SPANNER 52mm
1 × $11.00 -
Flasher Lamp, Front & Rear (no bulb)
1 × $14.03 -
WRENCH, WHEEL NUT - HEAVY DUTY
1 × $20.63 -
HT Lead Ignition Spark Tester
1 × $49.50 -
Exhaust Manifold Gasket
1 × $14.85 -
Australian Made Sticker
1 × $9.90 -
ENGINE MOUNT, LEFT + RIGHT - JAGUAR XE RWD 4 CYLINDER MODELS
1 × $165.00 -
Clutch Plate - Freelander & Rover (AP Driveline)
1 × $148.23 -
Alloy Wheel Nut Socket - 27mm
1 × $28.60 -
Headlamp Bucket Kit, (Bowl) Suit 7'' Lamps - CHROME BEZEL
1 × $40.00 -
Grease Nipple Multi Use
1 × $2.70 -
Adjustable Suspension Height Kit, Front, Ripspeed Type
1 × $183.70
Suspension
-
$209.00
Adjustable Front Lower Arm Kit (Pair)
One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required.
Sold in pairs only.
-
-
-
-
$37.40
Ball Foot & Cup Assembly, Front only
Built in 4.33mm Spacer
-
-
-
-
-
-
-
Availability: This product is currently out of stock.
Ball Joint Separator – Cup Type
Carbon Steel
Thrust nut for leverage
Jaws : 22mm W – 20mm D – 50mm opening -
-
$8.95
Idler Gear Bearing, 1.004″ OD
Upper Control Arm Bearing, Front Suspension
The 25.4mm wide original genuine bearing to take 19.05mm size idler gear shaft and sits in the gearbox case on early 3 synchro types and also in the early type clutch case.
-
$13.20
Bolt, Front S/Frame Tower to Body, (Dry)
Upper Control Arm Use with # 21A2694 Spacer