-
Alternator Conversion Plug, 5 Terminal to 3 Terminal
1 × $33.00 -
Bush, Front Lower Caster Arm - D5/RRS/RR
1 × $59.68 -
Electronic Ignition Conversion Kit Suit 43D, 45D & 59D Type Distributor
1 × $82.50 -
Setscrew, Multi use
2 × $1.05 -
Moulding Clip Snapsac Retainer - for Land Rover
1 × $1.10 -
BLADE - WIPER - REAR
1 × $15.02 -
BRAKE MASTER CYLINDER - SWB SERIES LAND ROVER
1 × $151.53 -
Exhaust Pipe, 1-7/8" Dia Suit Extractors
1 × $46.20 -
Battery Cable to Body Earth, Screw in fitting
1 × $6.60 -
BOOT KIT, FRONT (TDB500080/90) - DISCOVERY 3/4/RANGE ROVER SPORT
1 × $42.63 -
Fuel Filter, Inline, EFI, MANN/MAHLE
1 × $22.00 -
HEADLAMP BULB, MAIN BEAM
1 × $95.48 -
Brake Light Switch
1 × $8.53 -
Chrome Window Winder Handle
1 × $29.65 -
Timing Chain Tensioner
1 × $55.83 -
Alternator 65 Amp Multi Groove V Belt, Rover MPI
1 × $224.10 -
ELECTRONIC IGNITION KIT - 6CYL DISTRIBUTOR TYPE
1 × $99.00 -
Colour Tune, Single Plug Kit, 14mm
1 × $126.50 -
Adaptor Fuel Bowl To Carby L/Hand 30 Degree
1 × $16.78 -
Fir Tree Fixing - for BMW, Chrysler, Ford, GM, Land Rover
1 × $1.65 -
HT Lead Ignition Spark Tester
1 × $49.50 -
O Ring, Fitted to Distributor Drive Housing All Pre A Plus engines
1 × $1.65 -
BRAKE FLUID TESTER
1 × $55.00 -
SENSOR - EXHAUST GAS - OXYGEN
1 × $137.50 -
BONNET LATCH
1 × $47.74 -
Rotary Hoist Frame
1 × $87.44 -
WRENCH, WHEEL NUT - HEAVY DUTY
1 × $20.63 -
Filter Oil, Element - AJ 2.0L
1 × $11.94 -
Boot Kit, Pot Joint, Inboard CV
1 × $11.50
Suspension
-
$209.00
Adjustable Front Lower Arm Kit (Pair)
One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required.
Sold in pairs only.
-
-
-
-
$37.40
Ball Foot & Cup Assembly, Front only
Built in 4.33mm Spacer
-
-
-
-
-
Availability: This product is currently out of stock.
Ball Joint Separator – Cup Type
Carbon Steel
Thrust nut for leverage
Jaws : 22mm W – 20mm D – 50mm opening -
$8.95
Idler Gear Bearing, 1.004″ OD
Upper Control Arm Bearing, Front Suspension
The 25.4mm wide original genuine bearing to take 19.05mm size idler gear shaft and sits in the gearbox case on early 3 synchro types and also in the early type clutch case.
-
$13.20
Bolt, Front S/Frame Tower to Body, (Dry)
Upper Control Arm Use with # 21A2694 Spacer
-
$9.52
Bolt, Mount Bracket, Engine & Radiator
Also Front Tower Bolts Hydrolastic Front Subframe
-
$3.52
Tie Bar to Lower Arm Bolt. 5/16″unf by 1.3/8″long.
Original Bolt with a special length shank for the front suspension tie bar to the lower arm. Always check this out for any signs of wear and replace accordingly.
BH605141 is the exact correct length shank but slightly longer thread if required
-